PRIMARY CRUSHING / RP-JC-1200
Jaw Crusher
Primary crushing for hard rock and ore.
- Listed capacity
- 150–350 t/h
- Maximum feed
- 750 mm
Capacity depends on feed properties, feeding continuity and discharge setting. Confirm the final configuration for your site.
Request a configuration
THE PRIMARY STAGE
Reduce large feed.
Prepare the next stage.
The RP-JC-1200 Jaw Crusher reduces large rock and ore for downstream processing. A heavy welded frame, deep crushing chamber and hydraulic discharge adjustment make it suitable for the primary crushing stage in quarries, metal mines and aggregate plants.
Built around primary-stage duty.
Heavy welded frame
The frame supports the crushing assembly under primary-stage loads. Foundation and installation design must account for site conditions.
Deep crushing chamber
The chamber provides space for compression crushing. Controlled, even feeding helps maintain a continuous material flow.
Hydraulic discharge adjustment
A 100–200 mm discharge setting allows adjustment to suit the next processing stage. The setting is not a guarantee of the complete product size distribution.
Reversible jaw plates
High-manganese jaw plates can be reversed according to wear condition. Overload protection and routine inspections support load management.
Where it fits.
Use it for primary reduction in hard-rock quarries, run-of-mine ore preparation and aggregate plants. Confirm hardness, abrasiveness, moisture and maximum lump size. Clay-rich or sticky feed requires a review of feeding and prescreening arrangements.
One stage in a matched circuit.
Feed enters the chamber and is compressed between the moving and fixed jaws before discharging below. A typical circuit combines a feeder, jaw crusher, secondary crusher and screen. Capacity and transfer interfaces should be matched across the circuit.
- Feeding
- Jaw crushing
- Secondary crushing
- Screening
Engineering & installation interfaces.
PENDING CONFIRMATION
Site-specific drawings required
Dimensioned installation drawings, foundation loads, transport envelope, lifting points and interface dimensions have not been supplied for this preview. Obtain the approved drawing package before civil works or installation.
RP-JC-1200 technical specifications.
| Parameter | Value |
|---|---|
| Feed opening | 1200 × 900 mm |
| Maximum feed size | 750 mm |
| Discharge setting | 100–200 mm |
| Capacity | 150–350 t/h |
| Main motor power | 132–160 kW |
| Machine weight | Approx. 50 t |
The capacity range is conditional, not a guaranteed site output. Motor selection is subject to the final technical proposal.
Understand the operating limits.
Provide the material, maximum lump size, required hourly throughput, downstream feed limit and power supply. The listed 150–350 t/h range depends on feed properties, feeding continuity and discharge setting. Confirm the motor selection in the final technical proposal.
PENDING CONFIRMATION
Performance curves not supplied
No measured throughput curve or test report is available in the materials. Site output and product grading require project-specific confirmation.
Prepare a useful equipment brief.
Start with the inputs below, then compare the entire crushing circuit rather than the machine rating alone.
- Raw material, hardness, abrasiveness and moisture
- Maximum lump size and feed distribution
- Required hourly throughput and finished sizes
- Downstream feed limit, screening and recirculation
- Project location, power and installation conditions
Packing, delivery & support.
Minimum order: 1 unit. Lead time: 30–45 days, subject to the agreed order schedule. Supplied with export wooden case or steel frame packing; confirm shipping arrangements for the destination and transport dimensions. Installation drawings, an operating manual and remote technical guidance are available. On-site supervision and operator training can be arranged for the project.
These are source-supplied purchasing conditions for discussion. Confirm the lead time, scope and shipping arrangements in the order; no universal delivery commitment is made.
Questions before you specify.
Can it produce finished aggregate on its own?
It is intended for primary crushing. Projects requiring graded products generally need downstream crushing and screening.
How should I choose the discharge setting?
Consider both required throughput and the feed limits of downstream equipment. Share the circuit requirements for configuration advice.
Which areas need routine attention?
Inspect jaw plate wear, fasteners, lubrication points and transmission components. Follow the manual and adjust maintenance to operating duty.
Project & qualification evidence.
PENDING CONFIRMATION
Evidence under review
No approved customer case, certificate original or independent test report is attached to this product record. Generic scene images must not be treated as project evidence.
Start with your material.
Share the material, maximum feed size, required capacity, finished sizes and project location. Include downstream equipment and power supply where available.
Prefer email? 18337606870@163.com
Form preview only. Online delivery is not connected. No information is sent.